Prior to lighting your barbeque, visually check all hoses before each use for nicks, cracking, abrasions or cuts. If the hose is found to be damaged in any way, DO NOT USE YOUR BARBEQUE. A replacement hose and regulator is required (see the ‘PARTS LIST’ in Assembly Brochure).

IMPORTANT

  • Always raise the barbeque lid before lighting.
  • Do not lean over the barbeque when lighting the burner.
  • Visually check the flames every time you light your barbeque. If the flame is abnormally small or smokey yellow -- shut off the barbeque and check the venturi tubes for blockage or refer to the Troubleshooting Guide.

On barbeques with dual controls, the right control knob operates the right burner and the left knob operates the left burner. On barbeques with triple control knobs, the far left knob operates the rear rotisserie burner. The side burner control knob is located on the side shelf with the side burner (see figure above).

PROPANE MODELS ONLY

If the heat output from the burner(s) seems abnormally low, it may be caused by the regulator flow-limiting device being activated by a leak in the gas system, or improper lighting procedures. If this is suspected, shut off the cylinder valve and all burner valves. Perform a leak test to determine if a leak has caused the flow-limiting device to activate. If the leak test is negative, then carefully follow the lighting procedures step-by-step, ensuring all valves (including tank) are off before starting.

MAIN BURNER

Using The Ignitor

  1. Open the lid before lighting.
  2. Turn off all of the burner control knobs and close the gas supply valve.
  3. Open the gas supply valve and wait 5 seconds.
  4. Push in and turn a single main burner control knob to ‘HIGH’. All other control knobs should be in the "OFF" position.
  5. Turn or depress the ignitor, repeat if necessary.
  6. If the burner does not light immediately (within four seconds), turn burner control knob off and wait 5 minutes to clear the gas.
  7. Repeat steps 1 to 6. If burner still fails to light, refer to the Troubleshooting Guide to determine the cause and solution, or try the Match Lighting procedure below.

Match Lighting Procedure

  1. Open the lid before lighting.
  2. Place an ignited lighter or lit match through the lighting hole, approx. 1.25 cm (1/2") from burner.
  3. Push in and turn the left side main burner control knob to ‘HIGH’. The burner should light immediately (within four seconds). If it does not turn off the control knob, extinguish the lighter or match, and wait 5 minutes for gas to clear.
  4. Repeat steps 1 to 4. If burner still fails to light, refer to the Troubleshooting Guide to determine the cause and solution.

Lighting The Other Side Of The Dual Burner
Once one side of the dual burner has been lit, push in and turn the other control knob to ‘HIGH’. The unlit burner will light automatically.

SIDE BURNER (OPTIONAL)

Using The Ignitor

  1. Push in and turn the side burner control knob to ‘HIGH’.
  2. Turn or depress ignitor. Repeat if necessary .
  3. If burner does not light immediately (within four seconds), turn the burner control knob off, and wait 5 minutes to clear the gas.
  4. Repeat steps 1 to 3. If burner still fails to light, refer to the Troubleshooting Guide to determine cause and solution, or try the match lighting procedure below.

Match Lighting Procedure

  1. Place an ignited lighter or lit match near the ports, approximately 1.25 cm (1/2") from burner.
  2. Push in and turn the side burner control knob to ‘HIGH’. The burner should light immediately (within four seconds). If it does not, extinguish the lighter or match, turn the control knob off, and wait 5 minutes for the gas to clear.
  3. Repeat steps 1 and 2. If burner still fails to light, refer to the Troubleshooting Guide to determine the cause and solution.

REAR ROTISSERIE BURNER (OPTIONAL)

Match Lighting Procedure

  1. Open lid prior to lighting.
  2. Place an ignited lighter or lit match near the ports, approximately 1.25 cm (1/2") from burner.
  3. Push in and turn the rotisserie burner control knob to ‘HIGH’. The burner should light immediately (within four seconds). If it does not turn off the control knob, extinguish the lighter or match, and wait 5 minutes for gas to clear.
  4. Repeat steps 1 to 4. If burner still fails to light, refer to the Troubleshooting Guide to determine the cause and solution.

NOTE: DO NOT USE THE MAIN BURNERS WHEN THE ROTISSERIE BURNER IS LIT.

 
 
Where to Buy | Press Room | Corporate Login | Site Map


 Legal Disclaimer | All Content © Fiesta BBQ's 2003